mycnc:mycnc_et6
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
mycnc:mycnc_et6 [2020/04/27 11:33] – ivan | mycnc:mycnc_et6 [2023/03/16 09:23] (current) – ivan | ||
---|---|---|---|
Line 10: | Line 10: | ||
| RS485/RS422 | 1x RS485 with Modbus ASCII/RTU implementation | | | RS485/RS422 | 1x RS485 with Modbus ASCII/RTU implementation | | ||
| Computer connections | Ethernet (PC/ARM, Linux, MS Windows) | | | Computer connections | Ethernet (PC/ARM, Linux, MS Windows) | | ||
+ | |||
+ | //Note: The ET8 board is the new updated version of the ET6 controller, which requires unique firmware due to the use of a different chip.// | ||
==== ET6 Top View ==== | ==== ET6 Top View ==== | ||
Line 78: | Line 80: | ||
Connector pinouts for ET6 galvanic isolated inputs shown on a picture below | Connector pinouts for ET6 galvanic isolated inputs shown on a picture below | ||
- | {{:mycnc:007-et6-inputs-connection-001.jpg}} | + | |
+ | {{: | ||
Line 108: | Line 111: | ||
=== 3-wire NPN sensor connection example (external power supply)=== | === 3-wire NPN sensor connection example (external power supply)=== | ||
- | {{:mycnc:012-et6-npn-external-power-001-v2.jpg}} | + | {{: |
=== 3-wire PNP sensor connection example (external power supply)=== | === 3-wire PNP sensor connection example (external power supply)=== | ||
- | {{:mycnc:013-et6-pnp-external-power-001-v2.jpg}} | + | |
+ | {{: | ||
=== 3-wire NPN sensor connection example (internal power supply)=== | === 3-wire NPN sensor connection example (internal power supply)=== | ||
- | {{:mycnc:014-et6-npn-internal-power-001-v2.jpg}} | + | |
+ | {{: | ||
=== 3-wire PNP sensor connection example (internal power supply)=== | === 3-wire PNP sensor connection example (internal power supply)=== | ||
- | {{:mycnc:015-et6-pnp-internal-power-001-v2.jpg}} | + | |
+ | {{: | ||
< | < | ||
Line 128: | Line 134: | ||
===Switch connection example (external power supply)=== | ===Switch connection example (external power supply)=== | ||
- | {{: | ||
- | {{:mycnc:018-et6-switch-external-002-v2.jpg}} | + | {{:mycnc:et6-switch-external-001-2021-01.jpg}} |
+ | |||
+ | {{:mycnc:et6-switch-external-002-2021-01.jpg}} | ||
==== ET6 control board firmware reflash ==== | ==== ET6 control board firmware reflash ==== | ||
+ | |||
+ | // | ||
+ | |||
+ | :!: //**NOTE:** Make sure to select the firmware for the correct version/ | ||
+ | |||
+ | Flashing incorrect version of the firmware will result in a non-functional board. If you're unsure of your board version, please contact myCNC Technical Support prior to the reflash:// | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ---- | ||
{{: | {{: | ||
Line 146: | Line 163: | ||
- Open myCNC software on the Host computer, | - Open myCNC software on the Host computer, | ||
- goto Configuration Tab -> Support Tab | - goto Configuration Tab -> Support Tab | ||
- | - Set " | + | - Set " |
- Select " | - Select " | ||
- Set *UART port* to port with FT232 attached | - Set *UART port* to port with FT232 attached |
mycnc/mycnc_et6.txt · Last modified: 2023/03/16 09:23 by ivan