Differences

This shows you the differences between two versions of the page.

--- quickstart:mycnc-quick-start:probe_setup [2019/07/04 10:22] – ivan
+++ quickstart:mycnc-quick-start:probe_setup [2019/07/04 11:04] – ivan
@@ Line 9: / Line 9: @@
 ====Calibration/Adjustment of the probe sensor====
-In order to properly adjust the probe before starting the measurement procedure, it is necessary to eliminate any deviation that might be otherwise present in the probe. For this purpose, an indicator is used, as shown in the image below. This indicator should be sensitive to small forces of about 0.3-0.5 Newtons.
+In order to properly adjust the probe before starting the measurement procedure, it is necessary to eliminate any deviation that might be otherwise present in the probe. For this purpose, an indicator is used, as shown in the image below. This indicator should be sensitive to small forces of about 0.3-0.5H.
 {{:quickstart:mycnc-quick-start:probe-calibration-001-indicator-s.jpg}}
@@ Line 15: / Line 15: @@
 The spindle axis is moved by hand, and the amplitude of the sensor deviation is recorded using the indicator.
-The deviation is eliminated by turning the M2.5 adjustment screws with the 2mm hex key included in the probe kit:
+The deviation is eliminated by turning the M2.5 adjustment screws (shown in the image below) with the 2mm hex key provided in the probe kit:
 {{:quickstart:mycnc-quick-start:probe-calibration-002.jpg}}
-It is recommended to hold the key by a short lever, as to prevent excessive force application. It might be necessary to perform several cycles of spindle calibration to adjust the probe to have the minimum acceptable deviation.
+It is recommended to hold the hex key by its short lever as shown in the image below, in order to prevent excessive force application. It might be necessary to perform several cycles of spindle calibration to adjust the probe to have the minimum acceptable deviation.
 {{:quickstart:mycnc-quick-start:probe-calibration-003-s.jpg}}
@@ Line 78: / Line 78: @@
 =====Probe tools currently available=====
-The currently available CNC touch probe tools are the Wired Probe Sensor (SEN-PR-WR01), the Wireless Probe Sensor (SEN-PR-WL01), and the Wired Tool Setter (SEN-TS-WR01). The specifications for each of these tools can be found below.
+The currently available CNC touch probe tools are the Wired Probe Sensor (SEN-PR-WR01), the Wireless Probe Sensor (SEN-PR-WL01), and the Wired Tool Setter (SEN-TS-WR01). The specifications and technical characteristics for each of these tools can be found below.
-===Wired Probe Sensor===
+===Wired Probe Sensor (SEN-PR-WR01)===
+  * Unilateral repeatability: <0.003 mm
+  * Search directions: ±X, ±Y, -Z
+  * Deflection in XYZ directions: ±4mm
+  * Force to decouple in XY direction: from 0.5 to 0.8 H
+  * Force to decouple in Z direction: 2H
+  * Power supply: +5V
+  * Current consumption: <4mA
-===Wireless Probe Sensor===
+{{:quickstart:mycnc-quick-start:probe-size-drawing-001.jpg}}
-===Wired Tool Setter===
+===Wireless Probe Sensor (SEN-PR-WL01)===
+  * Unilateral repeatability: <0.003 mm
+  * Search directions: ±X, ±Y, -Z
+  * Deflection in XYZ directions: ±4mm
+  * Force to decouple in XY direction: from 0.5 to 0.8H
+  * Force to decouple in Z direction: 2H
+  * Latency delay: < 2 ms
+  * Error detection delay: < 0.33 ms
+  * Probe power supply: CR2032 3V
+  * Probe current consumption: <0.6mA
+  * Receiver power supply: 5-12V
+  * Receiver current consumption: 35 mA
+  * Radio channel radius: 6 meters
+  * Radio frequency: 2.4 GHz
+{{:quickstart:mycnc-quick-start:probe-size-drawing-002.jpg}}
+===Wired Tool Setter (SEN-TS-WR01)===
+The tool setter is designed to determine the exact coordinates of the tool mounted on a CNC milling machine using the contact method. The CNC system generates these coordinates as the tool comes into contact with the tool setter measurement platform, and uses them to calculate the height and diameter of the tool, to link the machining program to the work tool location.
+  * Unilateral repeatability: <0.003 mm
+  * Search directions: ±X, ±Y, -Z
+  * Deflection in XYZ directions: ±2mm
+  * Force to decouple in XY direction: from 0.5 to 2H
+  * Body diameter and length: D=28mm, L=60mm
+  * Base size: 28x28mm
+  * Diameter and height of the ceramic pad: D=10mm, h=2.5mm
+  * Power supply: +5V
+  * Current consumption: >4mA
+  * Features dust and splash protection
+  * Features a brittle safeguard fuse