mycnc:mycnc_et10
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
mycnc:mycnc_et10 [2019/04/29 10:54] – ivan | mycnc:mycnc_et10 [2019/04/29 11:49] – ivan | ||
---|---|---|---|
Line 4: | Line 4: | ||
24VDC is used to supply myCNC-ET10 control board. | 24VDC is used to supply myCNC-ET10 control board. | ||
The board contains 4 pins for connection +24V (joined internally) and a number of GND pins for convenient connection of external devices. | The board contains 4 pins for connection +24V (joined internally) and a number of GND pins for convenient connection of external devices. | ||
- | Power Supply | + | The 24V DC Power Supply |
{{hardware: | {{hardware: | ||
Line 11: | Line 11: | ||
==== Pulse-Dir outputs ==== | ==== Pulse-Dir outputs ==== | ||
- | ET10 has 6 channel pulse/dir outputs, | + | ET10 has 6 channel pulse/dir outputs, |
- | ET10 pulse dir outputs conform RS422 standard and compatible with most of servo and stepper drivers (line driver with paraphase signals positive and negative polarity). Internal schematic for pulse-dir is shown in a picture below. | + | ET10 pulse/dir outputs conform |
- | Pulse-dir schematic | ||
{{hardware: | {{hardware: | ||
Line 33: | Line 32: | ||
< | < | ||
- | An internal schematic is shown in the picture below. Darlington | + | An internal schematic is shown in the picture below. Darlington |
{{hardware: | {{hardware: | ||
- | ET10 pinout for outputs is shown below | + | ET10 pinout for the outputs is shown below: |
{{hardware: | {{hardware: | ||
- | There are LED indicators for each Output and PWM pin on the ET10 board to control actual Output/PWM state. LEDs are highlighted in a picture below. | + | There are LED indicators for each Output and PWM pin on the ET10 board to control actual Output/PWM state. LEDs are highlighted in the picture below. |
{{hardware: | {{hardware: | ||
Line 49: | Line 48: | ||
The ET10 control board has 48 galvanic isolated binary inputs, 12 groups of 4 inputs each. Each group has a common LED wire and separate power supply pins so inputs can be powered from different power sources. Using PNP and NPN sensors simultaneously is possible too. | The ET10 control board has 48 galvanic isolated binary inputs, 12 groups of 4 inputs each. Each group has a common LED wire and separate power supply pins so inputs can be powered from different power sources. Using PNP and NPN sensors simultaneously is possible too. | ||
- | Schematic of the 4 inputs group is shown in a picture below. | + | Schematic of the 4 inputs group is shown in the picture below. |
{{hardware: | {{hardware: | ||
- | Wires VCCB(common wire) and VCCA are used for external power supply connection. Beside external power supply, internal +24V DC can be used to supply input LEDs, if the correspondent jumpers are closed. < | + | Wires VCCB (common wire) and VCCA are used for external power supply connection. Beside external power supply, internal +24V DC can be used to supply input LEDs, if the correspondent jumpers are closed. < |
Jumpers to use the internal power supply for each 4-inputs group are shown in the picture below | Jumpers to use the internal power supply for each 4-inputs group are shown in the picture below | ||
Line 109: | Line 108: | ||
==== Spindle Speed control over DAC (0-10V) output ==== | ==== Spindle Speed control over DAC (0-10V) output ==== | ||
+ | |||
+ | The pinout for the spindle speed control over DAC is shown below: | ||
{{hardware: | {{hardware: |
mycnc/mycnc_et10.txt · Last modified: 2023/10/25 12:59 by ivan