Differences

This shows you the differences between two versions of the page.

--- mycnc:mycnc_et10 [2020/01/10 10:05] – ivan
+++ mycnc:mycnc_et10 [2020/01/27 10:32] – ivan
@@ Line 6: / Line 6: @@
 The 24V DC Power Supply and +24V and GND pins are shown in the picture below.
-{{hardware:et10:et10-connection-power-001.jpg}}
+{{:mycnc:et10-j27-001-power.jpg}}
@@ Line 19: / Line 19: @@
 PULSE-DIR channels 0,1,4,5 pinout
-{{hardware:et10:et10-connection-pulsedir-001.jpg}}
+{{:mycnc:et10-j27-002-pulse-dir.jpg}}
 PULSE-DIR channels 2,3 pinout
-{{hardware:et10:et10-connection-pulsedir-002.jpg}}
+{{:mycnc:et10-j27-003-pulse-dir-2.jpg}}
 ==== ET10 Output pins ====
-ET15 board contains ...  output pins-
+ET15 board contains 28 output pins-
   * 24 open collector outputs (OUT#0 ... OUT#23)
   * 4 PWM outputs (PWM#1, PWM#2, PWM#3, PWM#4)
-<code></code>
 An internal schematic is shown in the picture below. Darlington transistor array chips ULN2003 are used to buffer binary outputs in ET10. Each chip contains 7 transistors and handles up to 7 binary outputs. We recommend not to exceed 0.25A output current for each output pin (however ULN2003 maximum current is 0.5A according to the datasheet).
@@ Line 38: / Line 36: @@
 ET10 pinout for the outputs is shown below:
-{{hardware:et10:et10-connection-outputs-001.jpg}}
+{{:mycnc:et10-j27-004-outputs.jpg}}
 There are LED indicators for each Output and PWM pin on the ET10 board to control actual Output/PWM state. LEDs are highlighted in the picture below.
@@ Line 55: / Line 53: @@
 Jumpers to use the internal power supply for each 4-inputs group are shown in the picture below
-{{hardware:et10:et10-connection-inputs-002-key-04.jpg}}
+{{:mycnc:et10-j27-005-inputs-key.jpg}}
-{{hardware:et10:et10-connection-inputs-001.jpg}}
+{{:mycnc:et10-j27-006-inputs.jpg}}
 Connection Examples -
@@ Line 65: / Line 63: @@
 <code>External power supply. Jumpers are open.</code>
-{{:mycnc:et10-npn-external-001-v2.png}}
+{{:mycnc:et10-j27-007-npn-external.jpg}}
@@ Line 72: / Line 70: @@
 <code>External power supply. Jumpers are open.</code>
-{{:mycnc:et10-pnp-external-001-v2.png}}
+{{:mycnc:et10-j27-009-pnp-external.jpg}}
 === 3-wire NPN sensor connection example (internal power supply)===
@@ Line 78: / Line 76: @@
 <code>Internal power supply. Jumpers are open.</code>
-{{:mycnc:et10-npn-internal-001-v2.png}}}}
+{{:mycnc:et10-j27-008-npn-internal.jpg}}
 === 3-wire PNP sensor connection example (internal power supply)===
@@ Line 84: / Line 82: @@
 <code>Internal power supply. Jumpers are CLOSED.</code>
-{{:mycnc:et10-pnp-internal-001-v2.png}}
+{{:mycnc:et10-j27-010-pnp-internal.jpg}}
 === Switch connection example===
-  * Internal power supply <code>Jumpers for selected group are  closed.</code> {{:mycnc:et10-switch-internal-001-v2.png}} \\ \\ Common wire for 4 optocoupler units is connected to internal GND (0V) if the Jumper is closed. A switch should short another optocoupler input to +24V to activate input pin. \\ \\ Jumper should be closed to connect the optocoupler pin to +24V. A switch should short wire to GND(0V).
+  * Internal power supply <code>Jumpers for selected group are  closed.</code> {{:mycnc:et10-j27-011-switch-internal.jpg}} \\ \\ Common wire for 4 optocoupler units is connected to internal GND (0V) if the Jumper is closed. A switch should short another optocoupler input to +24V to activate input pin. \\ \\ Jumper should be closed to connect the optocoupler pin to +24V. A switch should short wire to GND(0V).
-  * External power supply (#1) <code>JUMPERS ARE OPEN</code> {{:mycnc:et10-switch-external-001-v2.png}}
+  * External power supply (#1) <code>JUMPERS ARE OPEN</code> {{:mycnc:et10-j27-012-switch-external-1.jpg}}
-  * External power supply (#2) <code>JUMPERS ARE OPEN</code> {{:mycnc:et10-switch-external-002-v2.png}}
+  * External power supply (#2) <code>JUMPERS ARE OPEN</code> {{:mycnc:et10-j27-013-switch-external-2.jpg}}
 ==== ET10 Encoder inputs ====
@@ Line 100: / Line 98: @@
 **ENCODERS** channels 0,1,2,3,4,5 pinout
-{{hardware:et10:et10-connection-encoders-001.jpg}}
+{{:mycnc:et10-j27-014-encoders.jpg}}
 ==== ET10 DAC +/-10V DAC outputs ====
-ET10 control board contains 6 channel +/-10V DAC outputs. This outputs can be used for analogue servo drivers closed-loop control, spindle speed control or any other application that requires IN analogue signals in +/-10V range.
+ET10 control board contains 6 channel +/-10V DAC outputs. This outputs can be used for analogue servo drivers closed-loop control, spindle speed control or any other application that requires IN analog signals in +/-10V range.
 Connectors XT16 and XT5 are used to connect DAC outputs. The connectors pinout is shown in the picture below
-{{hardware:et10:et10-connection-dac-001.jpg}}
+{{:mycnc:et10-j27-015-dac.jpg}}
@@ Line 139: / Line 138: @@
 Connectors XT20, XT21 are used to connect ADC inputs. The connector pinout is shown below
-{{hardware:et10:et10-connection-adc-001.jpg}}
+{{:mycnc:et10-j27-016-adc.jpg}}
 The picture below shows an example of a potentiometer connected to ADC2 input.
@@ Line 154: / Line 152: @@
 {{hardware:et10:et10-uart-001.png}}
-{{hardware:et10:et10-connection-uart-001.jpg}}
+{{:mycnc:et10-j27-017-uart.jpg}}