mycnc:global_variables
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:global_variables [2019/09/19 15:15] – ivan | mycnc:global_variables [2019/10/25 08:48] – ivan | ||
---|---|---|---|
Line 1: | Line 1: | ||
^ Variable Name ^ Variable Address ^ Comments ^ | ^ Variable Name ^ Variable Address ^ Comments ^ | ||
- | |GVAR_MODAL_G0_G3 |4001 | Modal state of G00, G01, G02, G03, G33, G34 | | + | |GVAR_MODAL_G0_G3 |4001 | Modal state of G00, G01, G02, G03 - motion |
- | |GVAR_MODAL_G96_G97 | + | |GVAR_MODAL2_G17_G19 |
- | |GVAR_MODAL_G68_G69 | + | |GVAR_MODAL3_G90_G91 |
- | |GVAR_MODAL_G98_G99 | + | |GVAR_MODAL5_G93_G94 |
- | |GVAR_MODAL_G20_G21 | 4006 | Modal state of G20, G21 | | + | |GVAR_MODAL_G20_G21 | 4006 | Modal state of G20, G21 - units | |
- | |GVAR_MODAL_G40_G42 | 4007 | Modal state of G40, G41, G42 | | + | |GVAR_MODAL_G40_G42 | 4007 | Modal state of G40, G41, G42 - cutter diameter |
- | |GVAR_MODAL_G25_G26 | + | |GVAR_MODAL8_G43_G49 |
|GVAR_MODAL_G22_G23 | 4009 | Modal state of G22, G23 | | |GVAR_MODAL_G22_G23 | 4009 | Modal state of G22, G23 | | ||
- | |GVAR_MODAL_G80_G89 | + | |GVAR_MODAL10_G98_G99 |
- | |GVAR_MODAL_G66_G67 | + | |GVAR_MODAL12_G54_G59 |
|GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 | | |GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 | | ||
|GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 | | |GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 | | ||
Line 445: | Line 445: | ||
| GVAR_ENCODER_Z_EVENT | 9070 | Stores info on the wheel of the encoder passing the zero mark (the zero position)| | | GVAR_ENCODER_Z_EVENT | 9070 | Stores info on the wheel of the encoder passing the zero mark (the zero position)| | ||
| GVAR_POPUP_MESSAGE | 9100 | +16. Allows to assign popup messages with either 0 for OFF or 1 for ON (for example, 9103,1 to bring up message #3). Popup messages examples can be seen [[plc: | | GVAR_POPUP_MESSAGE | 9100 | +16. Allows to assign popup messages with either 0 for OFF or 1 for ON (for example, 9103,1 to bring up message #3). Popup messages examples can be seen [[plc: | ||
+ | | | 9200 | +16. Reserved to display the encoder position on an infinite scale (no value turnover on every full encoder turn, instead the value will keep climbing indefinitely into the positives/ | ||
+ | | | 9216 | +16. Reserved to display the encoder position on an infinite scale WITH the current encoder dimension (to indicate the current encoder position) | | ||
| GVAR_SERVO_PID_ON | 60000 | Denotes that the servo PID is ON | | | GVAR_SERVO_PID_ON | 60000 | Denotes that the servo PID is ON | | ||
| GVAR_SERVO_PID_OFF | 60001 | Denotes that the servo PID is OFF | | | GVAR_SERVO_PID_OFF | 60001 | Denotes that the servo PID is OFF | |
mycnc/global_variables.txt · Last modified: 2024/05/13 15:45 by ivan