mycnc:gcodes_list
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:gcodes_list [2019/09/27 09:19] – ivan | mycnc:gcodes_list [2021/04/21 13:38] – ivan | ||
---|---|---|---|
Line 32: | Line 32: | ||
| G28.5 | Home Position #1 Restore | | | G28.5 | Home Position #1 Restore | | ||
| G28.6 | Home Position #2 Restore | | | G28.6 | Home Position #2 Restore | | ||
- | | G28.7 | Home Position #3 Restore | | ||
| G28.7 | Home Position #3 Restore | | | G28.7 | Home Position #3 Restore | | ||
| G28.9 | Home Position Address | | | G28.9 | Home Position Address | | ||
Line 69: | Line 68: | ||
| G64 | < | | G64 | < | ||
| G65 | G-code macro | M | | | G65 | G-code macro | M | | ||
- | | G73 | Cycle Deep Hole Drilling | M | | + | | G73 | [[mycnc: |
| G74 | Cycle Left Hand Tapping | M | | | G74 | Cycle Left Hand Tapping | M | | ||
| G76 | Cycle Lathe Thread | L | | | G76 | Cycle Lathe Thread | L | | ||
| G76 | Motion Mode Cancel| L | | | G76 | Motion Mode Cancel| L | | ||
| G80 | Cancel Motion Mode | | | | G80 | Cancel Motion Mode | | | ||
- | | G81 | Cycle Drilling | | | + | | G81 | [[mycnc: |
| G82 | Cycle Drilling Dwell | | | | G82 | Cycle Drilling Dwell | | | ||
- | | G83 | Cycle Peck Drilling | | | + | | G83 | [[mycnc: |
| G84 | Cycle Right Hand Tapping | | | | G84 | Cycle Right Hand Tapping | | | ||
| G85 | Cycle Boring No Dwell Feed Out | | | G85 | Cycle Boring No Dwell Feed Out | | ||
Line 94: | Line 93: | ||
| G97 | Set Spindle Speed | L | (revolutions per minute) | | | G97 | Set Spindle Speed | L | (revolutions per minute) | | ||
| G98 | Turn Feedrate per Minute | L | | | G98 | Turn Feedrate per Minute | L | | ||
- | | G98 | Canned Return Back to initial height | M | On mill machines, G98 allows to return the tool back to initial height Z during the canned return process. | + | | G98 | Canned Return Back to initial height | M | On mill machines, G98 allows to return the tool back to initial height Z during the canned return process. {{: |
- | {{: | + | |
| G99 | Turn Feedrate per Revolution | L | | | G99 | Turn Feedrate per Revolution | L | | ||
- | | G99 | Canned Return to a set height | M | As opposed to G98, which returns the tool to the initial height (height before cutting), G99 returns the tool to some set height Z. | + | | G99 | Canned Return to a set height | M | As opposed to G98, which returns the tool to the initial height (height before cutting), G99 returns the tool to some set height Z. {{: |
- | {{: | + | |
| G150 | Tool Correction Radius Set | | | G150 | Tool Correction Radius Set | | ||
^ Miscellaneous M-codes ^^^^ | ^ Miscellaneous M-codes ^^^^ | ||
Line 135: | Line 132: | ||
| M64 | Turn On binary output pin | PLC | | | | M64 | Turn On binary output pin | PLC | | | ||
| M65 | Turn Off binary output pin | PLC | | | | M65 | Turn Off binary output pin | PLC | | | ||
- | | M71 | Start Cutting | PLC | Cutting Tables | | + | | M71 | Start Cutting |
| M72 | Begin Plasma Marking Section | PLC | Cutting Tables | | | M72 | Begin Plasma Marking Section | PLC | Cutting Tables | | ||
| M73 | End Plasma Marking Section | PLC | Cutting Tables | | | M73 | End Plasma Marking Section | PLC | Cutting Tables | |
mycnc/gcodes_list.txt · Last modified: 2023/09/29 14:15 by ivan